- #PROTEUS 8 EXCESSIVE CPU LOAD HOW TO#
- #PROTEUS 8 EXCESSIVE CPU LOAD SOFTWARE#
- #PROTEUS 8 EXCESSIVE CPU LOAD CODE#
My question is not about pickit2, my question is "is the hex file produced with the build all directly suitable for use inpickit2 or i have to run the project in mplab environment and then compile and use that hex output file? " Please don't ask us any more questions about Pickit 2. In the Pickit 2 forum on the Microchip website.
#PROTEUS 8 EXCESSIVE CPU LOAD HOW TO#
If you have more questions on how to use the Pickit 2, then ask them If you need help on using Pickit 2, then read the Pickit 2 manual: Take the HEX file produced by "Build all" and go use it with the PicKit 2. If it's not the normal hex file produced on the regular build all from ccs then tell me how to produce the correct hex file. There's something wrong with my compiler, right?Ĭome one just a quick help on the hex file for burning the program on the pic.
#PROTEUS 8 EXCESSIVE CPU LOAD CODE#
The same code but with include doesn't work (the simulation on proteus don't work).Īnd the Microchip seller near my place only have the 18f4331.
#PROTEUS 8 EXCESSIVE CPU LOAD SOFTWARE#
My friend have a programmer and the pickit2 software and I want to take the files for him in order to burn the program on the pic.Īnyway, all I have to do is start a project in mplab and choose ccs compiler and include my source file and then compile in mplab and use the output files to burn the program ? Okay it seems like the help reached its limits lol.Īnyway at least can someone help me in burning the program on the pic? (ADC conversion clock period (5e-7 violates the minimum required TAD time). I chose the period to be result*7 but I should multiply "result" with a factor that gives me a 100% futy cycle if the result of the adc conversion is maximum and 0% if the result of the adc conversion is minimum.Īnd about this cpu excessive load, does this error exist in pic or only in simulators? Setup_power_pwm(PWM_FREE_RUN, 1, 0, POWER_PWM_PERIOD, 0, 1,2) Compare Postscale = 1 (Postscaler for Compare value) Compare = 0 (Timebase value for special event trigger) Period = 2000 (0-4095) Max value of PWM TimeBase TimeBase = 0 (0-65355) Initial value of PWM Timebase
![proteus 8 excessive cpu load proteus 8 excessive cpu load](https://www.howtodowith.com/wp-content/uploads/2020/12/proteus-_oscilloscope_hidden-1024x516.png)
Postscale = 1 (1-16) Timebase output postscaler Setup_power_pwm_pins(PWM_COMPLEMENTARY, PWM_off, PWM_Off, PWM_Off) Setup the 4 Power PWM channels as ordinary pwm channels. #define POWER_PWM_PERIOD 199 // 10 KHz pwm freq with 8 MHz osc. #fuses INTRC_IO, NOWDT, NOPROTECT, NOBROWNOUT, PUT If I run my program in mplab using the mplab plug-in tool I can burn my program using pickit ? (Someone already answered this but I prefer a much detailed answer if there's any). Surprisingly my program worked (with the 18f1330). I was thinking about using this 1330 instead of 4331 because the power pwm simulation worked for this 1330 and the same code didn't work for the 4331. In the file 18f1330.h I found that the parameter is declared #define NC_NC_NC 0x00 (there's a " _NC" missing ) Setup_Oscillator parameter not selected from Intr Oscillotar Config tab Setup_comparator(NC_NC_NC_NC) // This device COMP currently not supported by the PICWizard
![proteus 8 excessive cpu load proteus 8 excessive cpu load](https://i.ytimg.com/vi/Ro-DU3ASa40/maxresdefault.jpg)
![proteus 8 excessive cpu load proteus 8 excessive cpu load](https://i0.wp.com/www.microdigisoft.com/blogadmin/images/embedded/proteus/ultrasensor/main.png)
I tried to open a new project with the pic 1330.Īnyway without even writing a code i got some errors. I think that there's something wrong with my CCS. The frequency is stable at 10Khz (period=199 for a 8 mhz oscillator).Ĭan someone combine these 2 programs in one program ?Īnd by the way if i didn't use Proteus I would probably never have found out that if I don't feed the MCLR pin the program might not work.Īnd is there any other simulater (other than proteus, that works the same way, i will gladly get it if it works)Īnd PCM programmer, yes your program works, and as i said before it's on the pic 1330, and i edited it and had successfully generated 2 complementary pwms but that cpu load was my problem, while your original program that generated 3 power pwms without their complementary worked with a cpu load of 50%Īnd one more thing, when i create a new source file and i compile, most of the times the output files are generated in another folder that contains another program, why ? The result of the analog to digital conversion will determine my duty cycle. Now I need to combine both and my program is almost done. The first was an analog to digital converter (and it worked in Proteus with the 4331) and the other is the power pwm that only worked with the 1330. My problem with the 1330 is the CPU load.Īnyway guys, you have seen 2 functioning programs that I mentioned in this thread. Mike, the PIC is 1330 and not 1331, and the problem of these configuration bits things is happening with the pic4331 and not with the 1330. Send them to in writing in C language for a pic18f4331 Please do not post bug Reports on this forum.
![proteus 8 excessive cpu load proteus 8 excessive cpu load](https://www.researchgate.net/profile/Vivek-Kaundal-2/publication/259810151/figure/fig5/AS:392572062191619@1470607881785/Simulation-of-the-model-using-Proteus-View-1.png)
CCS :: View topic - help in writing in C language for a pic18f4331įAQ Forum Help Official CCS Support Search Register Profile Log in to check your private messages Log inĬCS does not monitor this forum on a regular basis.